Your Plumbing Crash Course: A Guide to Installing a Bathtub
Your Plumbing Crash Course: A Guide to Installing a Bathtub
Blog Article
Have you been searching for critical info concerning Tools You Need to Install a New Bathtub ?
Mounting a bathtub isn't specifically brain surgery, however it does call for solid plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately hard job. If the old bathtub is readily easily accessible, the task can move easily; if you need to open a wall surface to get rid of the old tub and also place the new bathtub, the job is much harder. In either case, the project is within a house handyman's abilities, although you will certainly need a helper to leave the old bathtub as well as set in the new one. Ensure you have certified yourself for the work and are comfortable trying it. Instead of working with a contractor to take control of a halfway-completed task, it is far better to take into consideration utilizing one before you start. Chances are you may need a professional plumber to make tube connections.
This post will assist you set up a new tub in your washroom if you have currently bought a brand-new tub and also do not require to change the plan of your previous water system pipes.
Your tools as well as product checklist ought to consist of the following:
Planning for the Installation
To start with, the supporting framework provided with the bathroom must be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the taps system to stop pressure on the bath tub.
Fit the flexible faucet ports to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its last position.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you should do is detach the water. After doing so, turn on the faucets to drain any kind of water continuing to be in the system. The procedure of removing the existing faucets can be quite problematic as a result of the limited accessibility that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have actually been removed, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from turning during this process. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Before going on to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Utilizing both wooden boards under its feet, place the bathtub in the required setting. The wood boards are useful in equally spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto four little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be achieved by examining the spirit level and adjusting the feet on the bathtub till the level reviews degree.
To set up taps, fit all-time low of the furthest flexible faucet connector to the ideal supply pipeline by making a compression join; after that do the same for the other tap.
Turn on the supply of water and also examine all joints and new pipework for leakages as well as tighten them if essential. Fill the bath tub and additionally examine the overflow outlet and the regular outlet for leakages.
Finally, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub must wait till the bath tub has actually been utilized at least when as this will certainly resolve it right into its final placement.
Fitting New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin guaranteeing that the washers remain in place in between the tap and the sink. Secure the tap in position with the producer given backnut. As soon as the faucet is safely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap adapters. The previous type ought to be connected to the tap ends initially, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to split a rigid seal, causing the water to permeate the wall between the bathroom and the tiling, resulting in problems with wetness as well as possible leaks to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your components as well as fittings. They are marketed in tubes and also cartridges, and can securing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bath tub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealer can break rather early if you do not take into consideration this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise easily readily available on the market. It is recommended to fit the tiles making use of water-resistant or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very serious about Tools You Need to Install a New Bathtub and I really hope you enjoyed the entire blog entry. Sharing is caring. One never knows, you may just be helping someone out. Thanks a lot for your time. Visit us again soon.
Immediate action for plumbing crises. Report this page